HaftClean activating surface cleaner

Name: HaftClean activating surface cleaner
Brand: Würth
SKU: 089010060

Surface activating cleaner
CLNR-STRUCADH-ACTIVATINGCLEANER-400ML

Art.-no. 089010060

EAN 4045727023037

All versions

Prices for customers after login

HaftClean activating surface cleaner

Art.-no. 089010060

Prices for customers after login

Quantity

Show availability in Würth trade store

Exclusively for trade customers

Locate trade store
Login/Register
Call customer service: 0800116633

Surface optimisation of non-porous surfaces

Good surface activation

Silicone-free

Notice

Not suitable for smoothing or removing adhesives/sealants.

Surface/material	Optimisation steps	Notes
Aluminium (AlMg3, AlMgSi1)	Activating Cleaner and, if necessary, AdhesionPlus primer for metal	Lightly sand with abrasive fleece beforehand if necessary.
Anodised aluminium	Activating Cleaner and, if necessary, AdhesionPlus primer for metal	-
Steel (St 37 etc.)	Activating Cleaner and, if necessary, AdhesionPlus primer for metal	Lightly sand with abrasive fleece beforehand if necessary. Steel components at risk of corrosion: 2-component PU or epoxy corrosion protection required.
Stainless steel (rustproof)	Activating Cleaner and, if necessary, AdhesionPlus primer for metal	Lightly sand with abrasive fleece beforehand if necessary.
Zinc-plated steel (hot-dip or conventional zinc plating)	Activating Cleaner and, if necessary, AdhesionPlus primer for metal	Lightly sand with abrasive fleece beforehand if necessary.
2-component top-coat paints (PU, epoxy), 2-component water-based primers and paints, cataphoretic paints, primers (EP/2C)	Activating Cleaner	Due to the large number of paints available, this information is only a guide. Please perform preliminary tests where necessary.
Powder coatings	Activating Cleaner	Preliminary testing is recommended for applications involving significant forces or a damp environment.
GFRP (unsaturated polyester), gelcoat side or SMC	Activating Cleaner	Lightly sand with abrasive fleece beforehand if necessary.
GFRP (unsaturated polyester), layup side	1. Lightly sand with S 80 2. Activating Cleaner 3. Primer for P/W/S	-
ABS	1. Lightly sand with abrasive fleece 2. Activating Cleaner 3. B and S Adhesion Plus for P/W/S	The sanding process can be omitted for parts subjected to little load.
Hard PVC	1. Lightly sand with abrasive fleece 2. Activating Cleaner 3. B and S Adhesion Plus for P/W/S	The sanding process can be omitted for parts subjected to little load.
Glass (mineral)	Activating Cleaner	Adhesive surface must be protected against UV radiation (opaque cover).
Glass ceramics	Activating Cleaner	-
Untreated wood and wood products (particle board)	1. Dust removal 2. Primer for P/W/S	-
Natural stone	1. Dust removal 2. Primer for P/W/S	Can cause discolouration when used with sensitive natural stone (marble).
Concrete, mineral mortar and plasters	1. Dust removal 2. Primer for P/W/S	-
Textiles, fleeces	Primer for P/W/S	Preliminary testing required; the adhesive gripping to the fabric may be sufficient.
The information always refers to the surface layer of the component (e.g. steel coated with 2-component epoxy paint: see 2-component top-coat lacquers). Important: The previous layer must be completely set and dry before each step. Observe the flash-off times!

The usage instructions are recommendations based on the tests we have conducted and our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee consistent quality of our products. We reserve the right to make technical changes and further develop products.

Product information

Würth Catalogue

Datasheets(X)

Safety data sheet

Certificates/ Documents

Application area

Alcoholic solution with adhesive substance for cleaning and improving adhesion of non-porous surfaces.

Instructions

The components must be clean, dry and free of grease. Either spray the surfaces with a thin coating and wipe off with a clean cloth or absorbent paper, or spray Activating Cleaner onto a cloth and wipe down the adhesive surfaces. Change the cloth/paper after each wiping process.

Flash-off time: At least 10 minutes.

For more information, please refer to the technical data sheet.

Contents	400 ml
Chemical basis	Solvent mixture with additives
Smell/fragrance	Alcohol
Colour	Transparent
Density/conditions	0.79 g/cm³ / at 15°C, DIN 51757
Min. flash-off time	10 min
Flash-off time conditions	at 23°C and 50% relative humidity
Min./max. processing temperature	15 to 25 °C
Min. flashing point	12 °C
Shelf life from production/conditions	24 Month / at room temperature
AOX-free	Yes
Silicone-free	Yes

Suitable glove:

Product

Description

Nitrile chemical protective glove With cotton velour finish inside

Description:

Permeation level: 5

Permeation is the process by which a chemical moves through the material of a protective glove on a molecular level. The time from the initial contact between the chemical and the glove to the permeation of the material is the breakthrough time.

Measured breakthrough time

Permeation level

< 10 min

≥ 10 min

≥ 30 min

≥ 60 min

≥ 120 min

≥ 240 min

≥ 480 min

Important information:

The information given is based on experience and laboratory conditions and is designed as a guide. However, the actual suitability of a glove depends on the individual conditions of its use and must be confirmed by an appropriate test under operational conditions. Given the variety of materials and chemicals used, the possibility of incompatibility or usage problems for the wearer cannot be excluded in individual cases. We would be happy to advise you about optimum solutions.